收藏本站
137
8024A–AVR–04/08
ATmega8HVA/16HVA
Figure 24-3. Switching NFET on and off during NORMAL operation
24.3
DUVR – Deep Under-Voltage Recovery Mode operation
The purpose of DUVR mode is to control the Charge FET so that the VFET voltage is above the
minimum operating voltage while charging cells below minimum operating voltage. This is useful
when the cell has been discharged below the minimum operating voltage of the chip. In DUVR
mode the Charge FET is switched partly on to provide a suitable voltage drop between the cell
voltage and the VFET terminal. As the cell voltage increases, the voltage drop across the
Charge FET will gradually decrease until the Charge FET is switched completely on. This means
that for high cell voltages, DUVR mode operation is equivalent to normal enabling of the Charge
FET (CFE=1).
ATmega8HVA/16HVA should operate in DUVR mode until software detects that the cell has
recovered from Deep Under-Voltage condition. When the cell has recovered from Deep Under-
Voltage condition, software should first set CFE=1. This is safe now since the cell voltage is
above minimum operating voltage. After that software should disable DUVR mode by setting
DUVRD = 1.
If both DUVRD and CFE bit is set before the cell voltage is above minimum operating voltage,
the VFET voltage will drop and the chip will enter BOD reset and switch off both the Charge- and
Discharge FET. Switching off the FET’s will cause the VFET voltage to rise again so that the
chip restarts from BOD reset, with DUVRD = 0 and CFE = 0 (default values). To avoid this, soft-
ware must always check the cell voltage by V-ADC measurements before setting CFE=1.
DUVR mode is default enabled after reset. However, while the chip is in reset state, DUVR
mode is disabled. This is a safety feature that ensures that the Charge FET will not be switched
on until the Charge Over-current Protection is operating. This implies that the DUVR mode will
be disabled from the time that a charger is connected until the selected start-up time expired.
During this period, the VFET voltage will be higher than the normal VFET Level in DUVR mode.
For more details about DUVR mode, refer to application note AVR354.
-1.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
11.0
12.0
Voltage
(V)
Time (ms)
100
200
300
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ATSAM3N4AA-AU MCU FLASH 48-QFP
ATSAM3SD8CA-CU IC MCU 2X256KB CORTEX-M3 100-QFN
ATSAM3U1EB-CU IC MCU 64KB CORTEX-M3 144-TFBGA
ATSAM3X8EA-CU IC MCU 2X256KB CORTEX-M3 144-BGA
ATTINY12V-1SUR IC AVR MCU 1K FLASH 4MHZ 8-SOIC
ATTINY13-20SQR IC MCU AVR 1KB FLASH 20MHZ 8SOIC
ATTINY13A-MMUR MCU AVR 1KB FLASH 20MHZ 10DFN
ATTINY13V-10SUR MCU AVR 1KB FLASH 10MHZ 8SOIC
相关代理商/技术参数
ATMEGA8HVA-4CKUR 功能描述:8位微控制器 -MCU AVR 8KB FLSH 512B EE 1KB SRAM - 4 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA8HVA-4TU 功能描述:8位微控制器 -MCU AVR 8KB, 512B EE 4MHz 1KB SRAM 1.8-9V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA8HVA-4TUR 功能描述:8位微控制器 -MCU AVR 8KB FLSH 512B EE 1KB SRAM - 4 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA8HVD-4MX 功能描述:8位微控制器 -MCU AVR 8KB, 512B EE 4MHz 1KB SRAM 2.1-8V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA8L-8AC 功能描述:8位微控制器 -MCU AVR 8K FLASH 512B EE 1K SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA8L8AI 制造商:Atmel Corporation 功能描述:
ATMEGA8L-8AI 功能描述:8位微控制器 -MCU AVR 8K FLASH 512B EE 1K SRAM ADC 3V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA8L-8AJ 功能描述:IC MCU AVR 8K 5V 8MHZ 32-TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:AVR® ATmega 标准包装:9 系列:87C 核心处理器:8051 芯体尺寸:8-位 速度:40/20MHz 连通性:UART/USART 外围设备:POR，WDT 输入/输出数:32 程序存储器容量:32KB（32K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:0°C ~ 70°C 封装/外壳:40-DIP（0.600"，15.24mm） 包装:管件